Thread: Cam break-in Procedure

Reply to Thread
Results 1 to 2 of 2
  1. #1 Cam break-in Procedure 
    Nice detailed write up by the guys at Erson Cams.


    Camshaft Break In Procedure

    Have a high quality service manual available, such as the factory service manual, or the vehicle specific manuals published by Chilton's, Motors, or Haynes. You will need these for the basic information regarding engine disassemble and reassemble along with the torque settings for the various fasteners.

    Read and understand the manual completely, along with these instructions before you begin working. We highly recommend you also have the assistance of a knowledgeable friend to assist you, especially during the initial fire-up and break-in period.

    In addition to the normal installation procedure, installing a performance camshaft requires you to check for several extra items to insure long life and optimum performance.

    New Lifters Are A Must- There is no such thing as a good used lifter! Any flat faced lifter establishes a wear pattern almost immediately with the cam lobe it is riding on and cannot be used on any other cam lobe, let alone a different cam. Should you have a need to disassemble the engine, make sure you keep the lifters in order so they go back on to the exact same lobes.

    Valve Spring Pressure and Travel- We highly recommend purchasing the matching valve springs recommended in our catalog. This insures you will have the proper pressures, both closed and open, and sufficient travel to get the maximum rpm, performance and life from your new cam.

    Piston to Valve Clearance- While many performance cams will work just fine with stock pistons, there are many factors that effect your engine and the clearance available. Things such as factory tolerances, normal machine work such as head and block surfacing; aftermarket components such as cylinder heads, higher ratio rocker arms, etc. all effect your engines ability to handle a performance camshaft.

    Valve Train Interference- In addition to valve spring travel and piston-to-valve clearance, a commonly overlooked area is that of retainer to seal clearance. The other common area of interference is rocker arm to stud clearance along with rocker arm travel. The best way to check these is by physically opening both a intake and an exhaust valve on each cylinder head to the gross lift of the cam plus and additional .030". It is easiest to do this by pressing down on the rocker arm with one of the many tools available. Do not simply rotate the engine to the maximum lift point for a given valve. This does not work when engines are hydraulic lifter equipped, or even allow any margin of safety when you are using a mechanical lifter cam.


    Valve Adjustment- The easiest way to insure proper adjustment is to adjust the rocker arms as you install them, one cylinder at a time. Adjust the intake valve as the exhaust valve is just starting to open and adjust the exhaust valve when the intake valve is almost closed. It is simplest to do this with the intake manifold off and watching the lifter's movement.


    Hydraulic Lifter Valve Adjustment- All engines, regardless of manufacture, require correct valve adjustment. Some engines, such as Chevrolet V-8's, are equipped with stud mounted rocker arms can easily be adjusted to compensate for changes incurred during engine assembly. Never just torque the rocker arm into place and assume that the lifter preload will automatically be correct. Various engine manufacturers use multiple length pushrods, shims, and spacers to compensate for changes in preload. Hydraulic lifters cannot compensate for all changes. Ideal lifter preload is .020" to .080". Do not attempt to fill the lifters full of oil prior to installation. They will fill automatically once started and manually filling them makes adjusting the preload a difficult task.

    Mechanical Lifter Valve Adjustment- Adjusting mechanical lifters should be done the same way as outlined above, one valve at a time. For an initial setting, we recommend .003" to .005" than listed on the cam's specification card. Once broken in and with the engine fully warmed up, re set the rocker arms to the cam's specification sheet.

    Installation Lubricants- All flat faced (non-roller) camshafts require the use of high pressure lubricant supplied with your Erson cam on the bottom of the lifters, the lobes of the cam and on the distributor drive gear. Do not use this lube on the tips of the pushrods, the sides of the lifters or on the rocker arms. Use quality oil when installing roller tappets.


    BEFORE YOU TURN THE KEY


    Fill All of the Engine's Fluids- Using a minimum of a SAE API SD, SE or better fresh clean mineral based oil and Erson's Break-In Additive with ZZDP , fill the engine to the proper level. Do not use synthetic oil during break-in. Fill the coolant system and follow the instructions on purging air from the system. With carburetor equipped engines, fill the carburetor to insure fuel is available immediately. Make sure that the ignition timing is properly set to insure immediate starting, without excess cranking of the engine.

    Pre-Lube the Engine- Using a oil pump priming tool such as those available from Mallory, spin the engine's oil pump until you see pressure on the gauge or have oil at the rocker arms. Do not attempt to prime the engine using the starter motor!


    Proper Ventilation- Make sure that you do not start the engine without good airflow. That means have the overhead garage door open and the exhaust vented to the outside. If you have any doubts about sufficient airflow to the engine, push the car out of the garage to make sure the radiator can draw in plenty of air. Having a fan to blow fresh air through the garage is a plus.

    Exhaust System- If at all possible, start the car with a muffled exhaust system hooked up and operational. It makes it much easier to hear what is going on.

    Resist the Urge- Take a minute before you try to start the engine for the first time and double check that you are ready to go. Don't take any short cuts or leave parts such as fan shrouds, air cleaner, wire looms, etc. off. Clean up the area around and especially under your vehicle. Pick up your tools and wipe up the floor so you can easily spot even a minor leak.

    Be Prepared- Have extra coolant or hose handy, clean rags, tools for tightening clamps, connections, etc. just in case. They need to be in place to make sure you have an uneventful break-in of the camshaft.

    WHEN THE ENGINE STARTS


    Have a Helper- Now is the time for a helper. They can check the coolant level, check for oil and fluid leaks, and proper operation of under hood accessories. Air pockets in the coolant system are common so make sure the recovery bottle is checked and filled as necessary. You cannot count on the temperature gauge. Temperature gauges are only accurate if the sensor is submerged in coolant and will not give an accurate reading if in an air pocket.

    Do Not Idle the Engine- As soon as the engine starts; raise the rpm to 2,000 rpm. You should also constantly vary the RPM between 2,000 and 3,000 RPM for the first 20 minutes. This is the only way to insure proper lubrication during this critical period since the camshaft to lifter contact area relies almost exclusively on oil splash from the crank and connecting rods. Make sure that you run the engine for a full 20 minutes using this procedure. It will seem like forever, but it is one of the most important steps to insure long, dependable performance.

    Once Break-in is Complete- Drain and replace the engine oil and filter with new, fresh oil and a new filter. Recheck for any fluid leaks and check all fluid levels. If you installed a mechanical lifter style camshaft, flat faced or roller style, the valve adjustment should be rechecked at this time with the engine fully warmed up. Hydraulic lifter equipped engines should not require any readjustment.

    Proper maintenance is important for any vehicle. Frequent oil changes, with a new filter is one of the easiest ways to insure your vehicle will deliver the performance you want for many long happy miles.


    Thanks
    Clint
    The Wedge Shop
    Last edited by The Wedge Shop; 03-05-2012 at 02:03 PM.
    The Wedge Shop
    Fast.British.Reliable.
    www.thewedgeshop.com
    Reply With Quote  
     

  2. #2  
    Spitfire
    Join Date
    Feb 2012
    Posts
    1
    very helpful post. so can we expect from a auto shop's post. actually been doing the replacement of this rover parts and when i read this post, i can now start my project. i am very thankful that i got this and i know everything happens for a purpose.
    Reply With Quote  
     

Similar Threads

  1. new cam break in
    By philman in forum Rover V8/Land Rover
    Replies: 5
    Last Post: 04-08-2010, 05:24 AM
  2. Cam Bolt.
    By Don Kelly in forum TR8
    Replies: 11
    Last Post: 04-01-2009, 07:07 PM
  3. Cam Choice?
    By bsa_m21 in forum TR8
    Replies: 8
    Last Post: 02-20-2009, 07:49 PM
  4. Cam Specs
    By JeffYoung in forum TR8
    Replies: 3
    Last Post: 09-05-2008, 04:20 PM
  5. Cam Theory and the Rover V8
    By Dan Jones in forum TR8
    Replies: 5
    Last Post: 06-15-2008, 02:57 PM
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts